GREDDY PROFEC B MANUAL PDF
May 26, 2020 | by admin
Guset User Download PDF. Publications: 93; Followers: 0. GReddy Profec B spec 2 Manual. Created Date: 8/14/ PM. Category: All. 0. Embed. Improper tuning of the Profec B-spec II may cause damage to the engine. GReddy 3 Way Fitting Double Sided Tape Air Filter Instruction Manual. Please make. pdf · Greddy Profec B 3 Knob Boost Controller Installation Instruction Manual, M. pdf · Greddy Profec B Spec Ii 2 Boost Controller Installation Instruction.
|Published (Last):||17 November 2013|
|PDF File Size:||8.71 Mb|
|ePub File Size:||7.20 Mb|
|Price:||Free* [*Free Regsitration Required]|
To fine-tune it, repeat steps 9 and 10 except this time only increase or decrease by 1 increment. PEAK is the peak boost value that the unit has seen since the last time it was cleared. Page 32 4 Reconnect the 12 pin Ignition harness back to the e-manage unit. Only one thin harness is required to be routed through the firewall. Page 53 Main Unit. Don’t show me this message again. Page 42 D e-manage Operation 1.
To do this, tune the unit to your desired boost pressure in fifth gear. Once you have followed these steps, you will have roughly tuned your unit. You should probably do this in a wide open area with no other cars nearby and preferably no cops. This page was last updated: In Good Maanual Condition. Unfollow manual turbo boost controller to stop getting updates on your eBay feed. Condition see all Condition.
Based on the very popular B-Spec. The maximum boost that you will see is also not consistent throughout the gears, which adds manhal more to the confusion. Overboosting may cause damage to the engine.
See pictures for actual item and condition. For more recent exchange rates, please use the Universal Currency Converter. The Display unit is packaged with the SD card already inserted.
Play Back Play back the recorded data in the display mode. See page 27 for throttle input signal setup. This setup demands a certain amount of trial-and-error to properly configure it since you have to make adjustments, then drive under WOT Wide Open Throttle and see what the maximum boost pressure achieved was throughout the entire RPM range.
For Breddy, 19psi kPa seems to be a safe setting based on what people on the forums have found since it is close to what the stock boost pressure is, yet there is an increase in power due to the Greddy unit keeping the boost close to 19psi while the stock boost tapers off as the RPMs increase. Boost Solenoid Valve Gredyd Product Features Take Boost feature. Does anyone have their profec-b settings for running like Indeed it is, that Spec2 is a tricky bugger.
Page 9 Installation Diagram Diagram 2: By pressing ‘print’ button you will print only current page. Don’t have an account? HKS turbo timer with ignition h Skip to main content. Comments to this Manuals Your Name.
GReddy PRofec B Quick Install User Manual | 1 page | Also for: PRofec A Quick Install
Format see all Format. Map Trace This feature will hi-light the cell that is currently reading. Enter text from picture: To clear it, go to the peak boost display, and hold down the treddy knob until the unit beeps and “” is displayed. Change boost pressure units to psi if so desired see manual. Vehicle with factory boost controlling solenoid valve Dual Port Actuator Disconnect the connector and the vacuum lines off from the solenoid valve and plug up the all the vacuum ports.
You don’t really manuao to know exactly what that means. When a setting is changed, it will send it to e-manage automatically. The Peak Hold type can be selected.
PROFEC BOOST CONTROL
Use the optional External Input Signal Harness sold separately and select one to use proefc output signal. Unfortunately, if you’ve already increased your start boost to the maximum setting that doesn’t give you surging, then there seems to be no way to get around this variance in boost pressure from low to high gears.
The following steps should be taken in exactly this order, taking into consideration all of the previous information: See each listing gredy international shipping options and costs. Don’t you make more than 14psi if your wastegate hose is disconnected?
Includes Controller Vacuum hoses 2 sizes Solenoid val UNIT Select the unit for the selected meter type. Pressure Sensor Harness Part: This will allow the values below the inputted value throttle opening to be recognized as accelerator OFF fully closed.
Also See for e Instruction manual – 55 pages. Did you read the thread at all?