AD162 DATASHEET PDF

May 27, 2020   |   by admin

AD Datasheet PDF Download – Transistor, AD data sheet. Tube AD or Röhre AD ID, Transistor, SPECIAL TUBEBASE in general and Power/Output shown. Radio tubes are valves. AD Datasheet, AD PDF, AD Data sheet, AD manual, AD pdf, AD, datenblatt, Electronics AD, alldatasheet, free, datasheet, Datasheets, .

Author: Samull Turn
Country: Bermuda
Language: English (Spanish)
Genre: Politics
Published (Last): 1 July 2010
Pages: 352
PDF File Size: 1.33 Mb
ePub File Size: 8.12 Mb
ISBN: 914-4-29050-593-5
Downloads: 16138
Price: Free* [*Free Regsitration Required]
Uploader: Grotilar

V decreasesby approximately 2. Thus the functions of the three locks are as indicated in Fig. TO Collector connected to the metal part of the mounting surface. Voltage Regulator Diodes, Transient Suppression Diodes The first letter indicates the nominal percentage tolerance in the operating voltage Vz.

J 0. Conversely, for matched pairs with a higher gain, the resultant negative feedback is increased and a higher h pE ratio will maintain the ad1622 protection against distortion. Current Collector current d. T m i, The temperature of the surface making contact with a heatsink. Ieiav max The maximum permissible average value of the total emitter current. No attempt should be made to force lock ‘A’ through this type of board.

The list of these ratings and their definitions is given as follows: Continue this light pressure until both the ‘A’ locks of the rear two leads are inside the holes Fig. The BC is primarily intended for low noise input stages in tape recorders, high quality amplifiers and other audio frequency equipment. For example, when a power transistor with an inductive. The final letter R is used to denote a reverse polarity version stud anode where applicable.

  A PRIVATE WAR WFRP PDF

The equation used is: The BC is a general purpose l. These additions are as follows: The definitions of the three systems accepted by the International Electro- technical Commission are as follows: Explanation of Handbook Datasheet 1.

These values are chosen by the device manufacturer to provide acceptable serviceability of the device, taking responsibility for the effects of changes in operating conditions due to variations in the characteristics of the device under consideration.

Ic av max The maximum permissible average value of the total datasheef current.

AD162 Datasheet

This occurs when the quiescent state is wd162 by the overload conditions. In many applications, however, the reverse-bias breakdown characteristics are also of importance. Care should be taken not to bend the leads nearer than 1. The thermal impedance curves for the BD are shown in Fig. The leads above this point should be clamped during any lead bending operations.

The rating also includes the switch off current. Base current ratings Datashet max Ib av max liut AV max IllM The maximum permissible base current without further qualification, the dc value is implied.

  DIFFERENTIABLE MANIFOLDS LAWRENCE CONLON PDF

A further linear interpolation between datssheet two 1 -7ms areas is then needed to approximate to the 1 -7ms SOAR at duty cycle of To assist in determining the rating in this second area, further curves are provided relating the voltage rating to external circuit conditions, for example: Hole spacing in either type oi grid allows the insertion of the “Lockfit” pins; but as the holes of the datasheey spaced t-grid are necessarily of smaller diameter than those of the other grid, the pins cannot be or should not be pushed in beyond the middle expansion – lock ‘A’.

AD Datasheet, AD PDF, Pinouts, Circuit – ETC

This is noted by an abrupt switching of the collector-emitter voltage to a low value at point D. Example B2 In multiple unit devices the terminal subscripts shall be modified by a number preceding the terminal subscript. Voltage, current, power and thermal ratings. The permissible total power dissipation is dependent upon temperature and its relationship is shown by means of a chart as shown in figure 3.

A general relationship for the approximate second harmonic distortion, d 2genera- ted by current gain mismatch, is given by the expression: